Released in November 2021
TAMIYA 1/48 Grumman F-14A Tomcat (late model) launch set. T61122F14A Tomcat Released in November 2021
[Product Introduction]
TAMIYA 1/48 Grumman F-14A Tomcat (late model) launch set. Reproduce the launch scene with many special parts including the main wing! From the start of deployment in 1973 until its retirement in 2006, the US Navy's F-14 Tomcat continued to fly as the world's strongest carrier-based fighter aircraft. Developed as a fleet air defense fighter that combines powerful radar and long-range missiles. Among them, the first mass-produced type and the most produced was the F-14A. Various improvements were made to each part of the A type during its long operational period. Many of the F-14As from the late 1980s onwards, which are classified as late models, are equipped with engines with improved reliability, and are equipped with a telephoto camera pod (AN/AXX-1 TCS) under the nose. Enables enlarged display of distance targets. Additionally, an AN/ALQ-126 ECM antenna has been added to the lower front of the wing glove to intercept enemy radar waves. Some aircraft have been modified to operate TARPS (Tactical Air Reconnaissance Pod System), which is equipped with three types of cameras. In addition, in the early 1990s, modifications began to give it ground attack capability, and it became possible to carry conventional bombs under the fuselage. Later, by equipping it with the AN/AAQ-25 Lanturn target designation pod, it became capable of operating laser-guided bombs, and the F-14A supported the US Navy as a multi-role fighter capable of performing a variety of missions. When the F-14 launches from an aircraft carrier, it requires the assistance of a steam catapult. The aircraft is connected to the catapult in a forward tilted position with the nose down, the variable main wings are extended to the forward position, and the leading edge slats and flaps are fully down in preparation for takeoff. In addition, the launch operation is supported by many flight deck personnel, and among them, the catapult officer (shooter) plays an important role in directing the catapult ejection operation and issuing the final instructions for launch. ★Total length 398, total width 408. In addition to the parts that are essential to reproducing the F-14 just before it is ejected from the catapult, such as the main wing with its moving blades activated and the retracted nose landing gear, we also have a paper sheet that realistically depicts the aircraft carrier's flight deck. , you can enjoy a tense ship departure scene. ★You can choose from two types of catapult spreaders (shuttles) that are attached to the front landing gear. ★The main spar parts that support the left and right wings are made of sturdy one-piece molding. ★Faithful modeling of later model features such as camera-equipped chinpod and electronic warfare antenna. ★A wide variety of weapons are included, including regular bombs, laser-guided bombs, lantern pods, reconnaissance camera pods, and late-model air-to-air missiles. ★The ejection seat, main instrument panel, side console, etc. are all faithful reproductions of the late A model. ★Includes 2 crew figures wearing late specification equipment. You can easily recreate the powerful scene immediately before ejection by deploying the variable wings to the forward position on the deck of an aircraft carrier and using the catapult. The dynamic pose of the catapult officer giving the departure signal on the deck is attractive. A deck sheet (made of paper, size 460mm x 276mm) that realistically depicts the details of the flight deck.Special parts for the F-14A Tomcat (late model). The main wing can be extended to its forward position to reproduce the state in which the leading edge slats and flaps are fully down. We have prepared a number of special parts such as various parts of the aircraft, inside the cockpit, and dolls that reproduce the launch scene and the characteristics of the late F-14A. The main wing is modeled with the leading edge slats and flaps deployed as separate parts. We have prepared an effect mark that expresses the concentric dirt pattern that is created in the area where the variable wing overlaps the over-fairing when it retreats. You can easily reproduce realistic dirt painting. Robust main spar part molded as one piece that connects the left and right wings. Secures the main wing at the correct angle for reliable assembly. (The parts in the photo are painted) The telephoto camera pod (AN/AXX-1 TCS) installed on the underside of the nose, which is a feature of the late F-14A, is also a highlight. In addition to a shortened nose landing gear that can reproduce the nose-down state at takeoff, two types of catapult spreaders (shuttles) are available. You can enjoy the powerful scene just before takeoff when the front legs are retracted and the ship leans forward. The canopy reproduces the bubble-shaped cross section using a slide mold. Three types of gas vent panels are available to release the gas fired from the 20 Gatling gun on the left side of the nose to the outside of the aircraft. You can select according to the marking to be produced. A set of crew figures are equipped with late-model equipment, such as a helmet without a visor cover. Two types can be selected according to the marking. (The parts in the photo are painted) There are two types of ejection seat cushions. We have also prepared simple shaped parts (on the right side of the photo) that are often seen on the late model F-14A. (The parts in the photo are painted) Instrument panels and side console panels can be selected according to the aircraft being manufactured. You can reproduce the details of the cockpit features of the late F-14A. (The parts in the photo are painted) The fairing of the antenna (AN/ALQ-126 ECM antenna) added to the front lower surface of the wing glove is also faithfully modeled. There are two types of main landing gear wheels to choose from depending on the specifications of the aircraft. A rich set of weapon parts such as air-to-air missiles, guided bombs, and reconnaissance camera pods. It can be installed according to the aircraft being manufactured. We also added Mk.82 regular bomb parts that are not included in the F-14A and F-14D kits. The engine nozzle reproduces the fully open state when using the afterburner, and the internal details are also impressive. The horizontal stabilizer is movable using a polycap. The airbags and ceiling panels that fill the gap between the main wing and the fuselage are made from parts designed for the main wing in its advanced state. 4 types of markings including the MiG shot down aircraft, notes on each part of the aircraft, and slide marks that reproduce the dirt pattern on the main wing. We also have mask stickers for canopy painting. Color diagrams introducing the 4 types of markings and a detailed actual machine manual will increase your motivation for production.
[Product specifications]
1/48 scale unpainted assembly kit□